<meta http-equiv="refresh" content="1; url=/nojavascript/"> Geological Stresses | CK-12 Foundation
Skip Navigation
You are reading an older version of this FlexBook® textbook: CK-12 Earth Science Concepts For Middle School Go to the latest version.

5.1: Geological Stresses

Difficulty Level: Basic Created by: CK-12
 0  0  0
Best Score
Practice Geological Stresses
Best Score
Practice Now

When people have too much stress they may break. What happens if a rock gets too much stress?

Lithospheric plates do a lot of moving on Earth's surface. Slabs of lithosphere smash into each other. They move sideways past each other along faults. Where conditions are right, magma rises through solid rock. It's no wonder that rocks experience stress! Rocks respond differently to different types of stress and under different conditions.

Types of Stress

Stress is the force applied to a rock. Plates experience stress when they collide, move apart, or slide past each other. Plates moving on a rounded surface experience stress. Stress happens to rocks on a smaller scale too. Local movements can cause stress in rocks.

There are four types of stresses that affect rocks:

  • Confining stress comes from the weight of all the overlying rock. This weight pushes down on a deeply buried rock. The rock is being pushed in from all sides, which compresses it. The rock will not deform because there is no place for it to move.
  • Compression stress squeezes rocks together. Compression causes rocks to fold or fracture ( Figure below ). When two cars collide, compression causes them to crumple. Compression is the most common stress at convergent plate boundaries.

Stress caused these rocks to fold.

  • Tension stress pulls rocks apart. Tension causes rocks to lengthen or break apart. Tension is the major type of stress found at divergent plate boundaries.
  • Shear stress happens when forces slide past each other in opposite directions ( Figure below ). This is the most common stress found at transform plate boundaries.

This rock has undergone shearing. The pencil is pointing to a line. Stresses forced rock on either side of that line to go in opposite directions.

Responses to Stress

The amount of stress on a rock may be greater than the rock’s strength. In that case, the rock will undergo strain or deformation ( Figure below ). Deep within the Earth, the pressure is very great. A rock behaves like a stretched rubber band. When the stress stops, the rock goes back to its original shape. If more stress is applied to the rock, it bends and flows. It does not return to its original shape. Near the surface, if the stress continues, the rock will fracture (rupture) and break.

With increasing stress, the rock undergoes: (1) elastic deformation, (2) plastic deformation, and (3) fracture.


  • compression : Stresses that push toward each other. This causes a decrease in the space that a rock can take up.
  • confining stress : Stress from the weight of material above a buried object. This reduces volume the rock is in.
  • deformation : Strain. The change of shape that a rock undergoes when it has been altered by stresses.
  • fracture : A break in rock caused by stresses. This happens with or without the movement of material.
  • shear : Parallel stresses that move past each other in opposite directions.
  • strain : Deformation in a rock when the stress that exceeds the rock's internal strength.
  • stress : Force per unit area in a rock.
  • tension : Stresses that pull material in opposite directions.


  • Stress is the force applied to an object. Stresses can be confining, compression, tension, or shear.
  • Rocks under stress may show strain or deformation. Deformation can be elastic or plastic, or the rock may fracture.
  • Rocks respond to stress differently under different conditions.


Use this resource to answer the questions that follow.


Select Overview.

  1. What is stress?
  2. What are the three directions in which stress can be applied?
  3. What does tension cause?
  4. What does compression cause?
  5. What is shearing?


  1. What type of stress would you find at a transform fault?
  2. What type of stress would you find at a subduction zone?
  3. Under what conditions will a rock fracture.

Image Attributions


Difficulty Level:



6 , 7

Date Created:

Jan 04, 2013

Last Modified:

Aug 24, 2014
Files can only be attached to the latest version of Modality


Please wait...
Please wait...
Image Detail
Sizes: Medium | Original
ShareThis Copy and Paste

Original text