Why is this lake so long and straight?
The photo is of Crystal Springs Reservoir near the San Francisco Bay Area. The water has collected in a low point in the land. The reason for the low point is a fault, the San Andreas Fault. On one side of the reservoir is the Pacific Plate. On the other side is the North American Plate. Would this be a good place to build a home?
A rock under enough stress will fracture. There may or may not be movement along the fracture. If there is not movement, the fracture is a joint. If there is movement, the fracture is a fault.
If there is no movement on either side of a fracture, the fracture is called a joint . Basalt rocks in Wyoming show horizontal and vertical joints ( Figure below ). These joints formed as the lava cooled and contracted.
Columnar joints in basalt in Wyoming.
If the rocks on one or both sides of a fracture move, the fracture is called a fault ( Figure below ). Faults can occur alone or in clusters. A cluster of faults creates a fault zone . Earthquakes happen when rocks break and move suddenly. The energy released causes an earthquake.
A series of faults offset this outcrop along Highway 191 in Moab, Utah.
Slip is the distance rocks move along a fault, as one block of rock moves past the other. The angle of a fault is called the fault’s dip . If the fault dips at an angle, the fault is a dip-slip fault ( Figure below ).
Imagine you are standing on a road looking at the fault. The hanging wall is the rock that overlies the fault. The footwall is beneath the fault. If you are walking along a fault, the hanging wall is above you. The footwall is where your feet would be. Miners often extract mineral resources along faults. They used to hang their lanterns above their heads. That is why these layers were called the hanging wall.
Block A is the hanging wall and block B is the footwall. The left diagram shows a reverse, or thrust, fault and the right diagram shows a normal fault.
In normal faults , the hanging wall drops down relative to the footwall. Normal faults are caused by tension that pulls the crust apart. This causes the hanging wall to slide down. Normal faults can build huge mountain ranges in regions experiencing tension ( Figure below ).
The Sierra Nevada Mountains in eastern California rose up along a normal fault.
An animation of a normal fault is seen here: http://earthquake.usgs.gov/learn/animations/animation.php?flash_title=Normal+Fault&flash_file=normalfault&flash_width=220&flash_height=320 .
When compression squeezes the crust into a smaller space, the hanging wall pushes up relative to the footwall. This creates a reverse fault . A thrust fault is a type of reverse fault. With a thrust fault the angle of the fault is close to horizontal. Rocks can slip many miles along thrust faults ( Figure below ).
In this thrust fault, the rock on the right is thrust over the rock on the left. The rock on the right has also started to fold because of this movement.
An animation of a thrust fault is seen here: http://earthquake.usgs.gov/learn/animations/animation.php?flash_title=Thrust+Fault&flash_file=thrustfault&flash_width=220&flash_height=320 .
A strike-slip fault is a dip-slip fault where the dip of the fault plane is vertical. Strike-slip faults result from shear stresses. If you stand with one foot on each side of a strike-slip fault, one side will be moving toward you while the other side moves away from you. If your right foot moves toward you, the fault is known as a right-lateral strike-slip fault. If your left foot moves toward you, the fault is a left-lateral strike-slip fault ( Figure below ).
Diagram of a right lateral strike-slip fault.
An animation of a strike-slip fault is seen here: http://earthquake.usgs.gov/learn/animations/animation.php?flash_title=Strike-Slip+Fault&flash_file=strikeslip&flash_width=240&flash_height=310 .
San Andreas Fault
The San Andreas Fault in California is a right-lateral strike slip fault ( Figure below ). It is also a transform fault because the San Andreas is a plate boundary. Unlike what some people think, California will not fall into the ocean someday. The land west of the San Andreas Fault is moving northeastward, while the North American plate moves southwest. Someday, millions of years from now, Los Angeles will be a suburb of San Francisco!
The San Andreas Fault runs up through California. This transform fault separates the Pacific plate on the west and the North American plate on the east.
People sometimes say that California will fall into the ocean someday. This is not true! This animation shows movement on the San Andreas into the future: http://visearth.ucsd.edu/VisE_Int/aralsea/bigone.html .
- dip : Angle of a fault relative to horizontal.
- dip-slip fault : Fault in which the dip of the fault plain is inclined relative to the horizontal.
- fault : Fracture along which one side has moved relative to the other.
- fault zone : Group of faults.
- joint : Break in rock along which there is no movement.
- normal fault : Dip-slip fault in which the hanging wall drops down relative to the footwall.
- reverse fault : Dip-slip fault in which the hanging wall pushes up relative to the footwall.
- slip : Distance rocks move along a fault.
- strike-slip fault : Fault in which the dip of the fault plane is vertical.
- thrust fault : Reverse fault in which the dip of the fault plane is nearly horizontal.
- A fracture with no movement on either side is a joint.
- Dip-slip faults show vertical movement. In a normal fault, the hanging wall drops down relative to the footwall. The reverse is true of a reverse fault.
- Strike-slip faults have horizontal motions due to shear stress.
Use the resource below to answer the questions that follow.
- Types of Faults at
- What causes normal fault motion?
- What type of motion results from a normal fault?
- Explain a reverse fault. What type of motion results from this fault?
- Describe a strike-slip fault.
- What causes an oblique-slip fault?
- Compare and contrast normal and reverse faults.
- Imagine you're looking at a cliff with layers of rock. What features would you see to indicate a fault?
- What is a strike-slip fault? What type of plate boundary can be a strike-slip fault or fault zone?